10″ × 2.5″ Sediment & Carbon Replacement Pack

Less grit. Better-tasting tap water.

Two replacement cartridges for a compatible 10″ × 2.5″ housing setup: 5 micron sediment filtration followed by CTO carbon for chlorine taste and odour.

Sediment filtration for sand, dirt and rust.
CTO carbon helps reduce chlorine taste and odour.
A matched pair for compatible standard 10″ × 2.5″ housings.

$42.00

Taxes included.

Free shipping over $100

Who this pack is for

Refresh the two stages you rely on.

Plan replacement around 6–12 months, depending on water quality and use. Check sooner if taste, odour or flow changes.

Less grit

Sediment catches sand, dirt and rust. Carbon helps reduce chlorine taste and odour.

For everyday drinking water.

Better showers

Carbon helps reduce chlorine and unwanted odour in your shower water.

For fresher water in the shower.

What's in the pack

One sediment cartridge. One carbon block.

The sediment stage handles particles; the carbon stage handles chlorine taste and odour. A straightforward replacement pair for your existing compatible setup.

Stage 01

5 Micron PP Sediment Filter — 10″ × 2.5″

Polyspun sediment media captures particles before they reach the carbon stage.

HFS-F01M-PP1025 $15.00

Full spec and documents

Stage 02

5 Micron CTO Carbon Block Filter — 10″ × 2.5″

Activated carbon adsorbs compounds that contribute to unwanted taste and smell.

HFS-FS01M-1025 $25.00

Full spec and documents

Individual prices vs this pack

Item Price

5 Micron PP Sediment Filter — 10″ × 2.5″ cartridge $15.00

5 Micron CTO Carbon Block Filter — 10″ × 2.5″ cartridge $25.00

Bought separately $40.00

This pack $42.00

Measure these two.

Measure the cartridge you're replacing, not its housing.

A Overall length — end to end, including caps or connectors

B Outer diameter — at the widest point of the body

Will it fit?

Standard 10″ × 2.5″ cartridge format.

This pair fits compatible open-sump cartridge housings. It is a different connection family from proprietary quick-fit filters, even where the length looks similar.

20″ × 4.5″ 508 mm × 114.3 mm 10″ × 4.5″ 254 mm × 114.3 mm 10″ × 2.5″ 254 mm × 63.5 mm ← this filter pack Quick-fit twist-off 300 mm × 65 mm Inline, hose fittings 260 mm × 50 mm

Measured it and still not sure?

Send a photo of the cartridge beside a tape measure and we'll tell you which size it is.

Call 0474 189 347 or email sales@homefiltrationsystems.com.

Contact us

Nominal sizes vary a little between makers, so match the measurement rather than the label. What we can't tell you is how ours compares to a cartridge we didn't make and haven't tested, or whether a replacement affects your housing's own warranty; that one is between you and its manufacturer.

Fitting it, what comes out, and when it's due again

Cartridge installation & replacement guide

Download the replacement guide (PDF)

Need help with the change? Call 0474 189 347.

What happens, in order

Turn off & release pressureShut off the supply and release pressure through a downstream tap or the relief button, if fitted.
Remove & cleanRemove the old cartridges, wash and rinse the bowls, and inspect the seals. Replace damaged O-rings.
Fit the replacementsSeat the correct cartridges centrally in their housings. Refit the bowls firmly by hand without overtightening.
Flush & checkRestore supply slowly with a downstream tap open. Follow the stated flushing time, then check housings and connections for leaks.

Reviews

What people who fitted it said.

Only buyers we can match to an order can leave one, so the count is lower than it would be otherwise.

FAQ

Questions about this replacement pack?

A few practical answers before you order or change your filters.

Talk to someone

Need help choosing? Call 0474 189 347.

Check two standard 10″ × 2.5″ open-sump housings and compare cartridge ends and seals. Proprietary quick-fit heads need their own matching replacements.

Plan around 6–12 months, depending on water quality and use. Check sooner if taste, odour or flow changes. Follow the rating and replacement instructions for your filters.

This pack lets you refresh the supplied set together. Individual stages can load at different rates; follow your system guide when a single cartridge needs earlier attention.

It has sediment and CTO carbon stages only. For hardness-related scale, PFAS or dissolved salts, ask HFS about a treatment setup designed for that separate purpose.

Follow your system’s isolation, pressure-release, fitting and flushing instructions. If you cannot isolate it safely or are unsure, arrange help from HFS or a qualified plumber.

Contact HFS before fitting or using the pack. Match dimensions, connectors and filtration purpose, and check your housing manufacturer’s warranty terms before using another brand.